AI DamageAltec Digger Derrick 2017: typische Probleme
Altec Digger Derrick 2017. Service-Bulletins des Herstellers für dieses Jahr: 21. Details nach Bauteil unten, mit Quellen.
Kennzahlen
- Technische Service-Bulletins (TSB)
- 21
Bauteile, über die sich Halter beschweren
| Bauteil | Halterbeschwerden | mit Unfall | Technische Service-Bulletins (TSB) |
|---|---|---|---|
| Ausstattung | 0 | 0 | 11 |
| Elektrik | 0 | 0 | 4 |
| Motor und Kühlung | 0 | 0 | 4 |
| Karosseriestruktur | 0 | 0 | 3 |
| Kraftstoffanlage | 0 | 0 | 2 |
| Feststellbremse | 0 | 0 | 2 |
| Antriebsstrang | 0 | 0 | 2 |
| Betriebsbremse | 0 | 0 | 2 |
| Stabilitätskontrolle (ESP) | 0 | 0 | 1 |
| Außenbeleuchtung | 0 | 0 | 1 |
| Sonstiges | 0 | 0 | 4 |
Vergleich
Was vor dem Kauf prüfen
- Elektrik. Alle Steuergeräte auslesen, Batterie und Lichtmaschine testen, Stecker nahe der Aufprallzone prüfen.
- Motor und Kühlung. Kühler und Lüfter nach Frontaufprall, Kühlmittelstand und -zustand, Überhitzung.
- Karosseriestruktur. Längsträger, Säulen, Spaltmaße, Spuren von Richten oder Schweißen.
- Kraftstoffanlage. Kraftstoffgeruch, Undichtigkeiten, unrunder Lauf, Codes der Kraftstoffanlage.
Service-Bulletins des Herstellers
Titel der Bulletins im Original (Englisch), wie bei der NHTSA eingereicht.
- Altec has learned that the king pin towing capacity placard might not be installed on certain DL derricks…
Altec has learned that the king pin towing capacity placard might not be installed on certain DL derricks built from August 2005 to October 2024. This could lead to unintentional overloading which could result in…
- Altec has learned that the structural subbase welds on certain DH derricks built from July 2016 to…
Altec has learned that the structural subbase welds on certain DH derricks built from July 2016 to December 2023 could contain stitch welds rather than the required continuous welds, which could result in cracks…
- Altec has learned that a 12-volt Airtronics relay installed in the PDM could have been manufactured to an…
Altec has learned that a 12-volt Airtronics relay installed in the PDM could have been manufactured to an insufficient threshold on certain units built from December 2004 to October 2022. This can cause the relay to…
- Altec has learned that on certain digger derricks built from January 29, 2015, to December 3, 2020,…
Altec has learned that on certain digger derricks built from January 29, 2015, to December 3, 2020, equipped with a Hetronic radio control system have experienced frequent dropouts or would not connect to the receiver…
- Altec has learned that an incorrect grade auger retention pin could be installed on certain DC, DL, and DM…
Altec has learned that an incorrect grade auger retention pin could be installed on certain DC, DL, and DM derricks built from July 2015 to August 2023. Over time, this could result in the pin becoming damaged.
- Altec Industries, Inc
has received notification from an Original Equipment Manufacturer (OEM) that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with Altec equipment…
- Altec has learned that certain digger derricks and aerial devices of various models built from January…
Altec has learned that certain digger derricks and aerial devices of various models built from January 2010 to January 2023 may contain access steps with a handrail and side plate that come together in a small space…
- The body compartment wiring on certain Altec aerial devices, digger derricks, and body-only units built…
The body compartment wiring on certain Altec aerial devices, digger derricks, and body-only units built from 2014 to 2021 contains an in-line fuse located close to the lighting in the compartment, while other units are…
- Altec has learned that the lift cylinder pivot pin retainers may bend or break during use on DT80 digger…
Altec has learned that the lift cylinder pivot pin retainers may bend or break during use on DT80 digger derricks built from March 2007 to October 2021. If the pin retainer fails, the pivot pin will still be held in…
- Altec has learned that the electrohydraulic outrigger/tools control valve on AA755L and A-series aerial…
Altec has learned that the electrohydraulic outrigger/tools control valve on AA755L and A-series aerial devices and DLB, DMB, and D2/3/4000B series digger derricks could have the potential to produce a very small…
- Altec Industries, Inc
has received notification from Navistar that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with Altec equipment. On certain trucks equipped with…
- Altec has learned that on certain derricks built from 2008 to 2020 the diameter of the wire winch rope…
Altec has learned that on certain derricks built from 2008 to 2020 the diameter of the wire winch rope installed may exceed the maximum allowable diameter specified by the ANSI A10.31 derrick standard based on the…
Die NHTSA führt 21 Bulletins für dieses Jahr; hier die 12 neuesten.
Andere Jahre dieses Modells
Fragen und Antworten
Was sind die häufigsten Probleme beim Altec Digger Derrick 2017?
Für dieses Jahr gibt es keine Halterbeschwerden in den NHTSA-Daten; die Daten stammen aus 21 Service-Bulletins des Herstellers.
Wie viele Service-Bulletins (TSB) gibt es für den Altec Digger Derrick 2017?
Die NHTSA führt 21 Service-Bulletins des Herstellers für dieses Jahr. Ein Bulletin sagt Händlern, wie ein bekanntes Problem diagnostiziert oder behoben wird; es ist kein Rückruf.
Lohnt sich ein Altec Digger Derrick 2017 von einer US-Auktion?
Halterbeschwerden beschreiben Mängel, keine Unfallschäden. Prüfen Sie vor dem Gebot die oben genannten Bauteile und die Fotos des Loses: VinWind erstellt per VIN einen Bericht über sichtbare und versteckte Schäden.
Andere Modelle von 2017
Lesen Sie auch
Quellen: öffentliche NHTSA-Daten (USA) – Service-Bulletins und Halterbeschwerden; YouTube – Links zu Videos mit Nennung der Autoren. Beschwerden sind Aussagen der Halter, von der NHTSA nicht bestätigt, und betreffen Mängel, keine Unfallschäden. Daten aktualisiert am 2026-11-04.